Відео

i worked in factory assemble cell phone 5 years. there are some point assembling waterproof tape 1. Do not touch anything with the tape surface. 2. The tape attachment surface must be free of scratches and any other substances. 3. The tape width is very thin, so it must be applied accurately. So factories use jigs. 4. After attaching the tape, you must press it with hot heat and constant pressure for about 5 to 10 seconds. Attaching it without heat as shown in the video above has no effect. 5. Nonetheless, you should always be careful with water after applying the tape. Because it was assembled by hand rather than a jig, it is difficult to predict how defects may occur. Therefore, if you apply tape but the waterproof performance does not work, the following causes may be found. 1. Presence of debris or dust between the tape and the part surface 2. There are scratches on the surface where the tape is applied. 3. Tape does not stick evenly 4. The tape is not subjected to the approved heat and pressure spec. 5. Use of unauthorized tapes! The use of unapproved auxiliary materials can be fatal in causing waterproofing failure. In this video, the heater was used and then rubbed by hand, but during actual assembly at the factory, a hot jig is used to press the entire surface where the tape is attached. Pressing after the heat has cooled is ineffective, and pressing while pushing gently with your fingers is also incorrect. The most important thing in waterproofing performance is proper heat compression!

RIP simcard tray

Worked, thank you so much for the help!

This helped me thank you bro🎉

No way I'm ever touching my ps5 insides.

Didn’t fix shit

Polished version might add the chip to a custom power board.

Maybe the missing FBU pins broke reversability.

Man makes a PoZidrive iPhone.

How much did you sell it for?

Im in the us i have a snapdragon s24

Where did u bought that parts at 11.30?

Actualy it work half hour after i make same things like you

Thank you your video helped me fix the bottons and stick drift

great video but for all this i might as well buy another controller. ill mess around and forget where the pieces go back

U ruined it

They complicated something so easy to access, wow, My ps4 controllers have lasted more than 7 years because i do maintenance to both of my controllers. They're pushing people to buy the playstation edge controller haha

The top camera nust have ois. If you look at the camera when its off and rotate the phone the lens drags to the bottom. They all do.

this was great

I need to know what plastic tool that is. I can't even open the sides because I don't have anything thin enough that won't break it.

Good channel this is.

*Thx bro you saved me money! Not as crazy as it looks. Took about 30 minutes. I used contact cleaner as well on the tiny disk piece. Thx again!* ❤

the future is here

Samsung treating Australian as 3rd world bruh

Cant clip them back in

Oh man, você já pode trabalhar na foxcom. Melhor canal de teardown que eu já vi! Detalhe por detalhe. Peça por peça e ainda remonta tudo. Parabéns!

Al final se hizo canon 2 generaciones después

Why?

Thx for the tut. I just used electronics cleaner by wd40 to clean the potentiometers.

Thanks a lot, fixed mine

I just fucked my controller.

purposely slow and full of advertising. nah.

What about an adapter lightening male with C female ports ?? Same idea of the adapter male C port with micro female port?!!!!!!

This didint age well

I liked the video as soon as I saw the fan return 😂

Why not type c?

😂

can you make my iphone 12 mini type c

I've seen a UA-camr who used type c cable to power the ps4, you should look into it . His name is TERA and he built the world's lightest ps4

who knew

Anyone from 2030?

What was the red and black wire you soldered back on, I have two additional ones yellow and green? I'm asking because I actually found one yellow one not even soldered on from factory 😔

great video. i just did this to mine but noticed they werent that dirty but my right stick has bad drift. i did notice when comparing the sticks the right ones wipes were much more compressed and bent them out to match the left stick that has no drift and the drift is gone. good stuff !

Can you do this on my phone for $50

i got an idea how about "i make a Lightning port iphone 15 pro max" or smt like that

пахнет loco клеем 😂

😂 عندما يطلع الكيف

Ich repariere iPhone und Samsung jeden Tag zu Hause.

Man was I rooting for you when you were soldering on that capacitor. The humor (like the bit about the extreme slow-motion removal of all 42 screws) really helps to watch this sort of technical videos (to a person new to the whole deal at least). And the fact that you show the whole process, errors, failed attempts and all, makes it really exciting - will it work? Anyway, thanks a bunch for the effort!

April Fools? This is a regular, run of the mill video with 10M views, where they take one thing from the mud, clean it, polish it, then present you with the same thing but brand new (probably before they put it in the mud). This time, instead of cursing the lying sum of beaches, I was laughing my bottom dollar off!